Traditional freestanding baths fall into a number of broad categories with regard to their basic shape, two other problems with equal significance are the style of foot and the type of faucet fittings required. Each of those and the principle kinds of traditional tub tub form are described below. The data in this article is about contemporarily manufactured traditional style freestanding baths not vintage baths.
Bathtub Foot Model
Traditional bath toes usually are available in one in all 4 broad kinds though the variation within those types will be great. Plain ft, ball and claw feet, often just called claw ft are in the type of a talon or claw gripping onto a ball which rests on the floor and takes the load of the tub, lions paw toes are shaped just like the paw of a lion standing on the lavatory flooring and then there are various more or less Art Deco model feet that you could find on just a few freestanding baths. Of those three categories the ball and claw toes are available such huge variation that the more stylised variations are barely recognisable as such with a lot of the detail gone. Plain ft are similar to the ball and claw usually shape but haven’t any detail on them.
Bathtub feet are available in various materials and finishes, cast iron toes should be painted, most often they are painted black, white or the same colour as the toilet walls. Toes are also available made from brass, either with a refined brass finish (which is usually used with gold faucets) or in electroplated chrome, gold (often called vintage gold), brushed nickel or bright nickel. Not all traditional baths have feet. Basically feet are usually not interchangeable between baths although they may generally be that specific manufacturers use the identical ft on two or more of their baths. You must by no means purchase a shower with out the feet unless you already know you will get the proper toes manufactured for that bath.
Roll High and Faucet Fittings
Its essential to know once you buy a traditional freestanding tub what sort of faucets you’ll use with it and what you will have to attractively plumb them in Traditional freestanding baths are sometimes called roll prime baths, this refers back to the rolling fringe of many traditional type of bath. It is not possible to mount a faucet onto the rolling fringe of a roll top bath. A traditional resolution to this was to drill the taps gap within the side of the bathtub just above the overflow the taps used are shaped to return up at proper angles to the water inlet so they’re in the identical type as a deck mounted set of taps. These taps are called globe taps, they usually come as a pair of faucets, hot and cold. Globe taps are only really used as of late with vintage cast iron roll prime baths.
More typically today roll top baths onto which faucets will be mounted have what’s called a tap platform. A tap platform is a flattened part of the tub edge into which tap holes will be drilled and taps mounted. For baths onto which taps cannot be mounted you’ll use both wall mounted or ground mounted taps. Note additionally that there are some contemporarily manufactured and, broadly speaking, traditionally styled baths that do not need a roll top as such and onto which faucets may in concept be mounted anywhere on the edge of the bath.
Traditional Single Ended
This is the simplest of the traditional bath types, its a degree topped tub sitting on 4 feet, in plan its rounded at the head end (the place your head would go when you have been mendacity in it) and flat on the foot end. The plug hole and overflow are on the foot finish of the bath. If it has a faucet platform that can also be at the foot end of the bath. Its distinguished from a slipper tub by being the identical height throughout the highest of the bath.
Traditional Double Ended
This is actually the identical because the traditional single ended tub but in plan it is rounded at both ends and the plug gap and overflow in the middle of one of the long sides of the bath. If it has a tap platform then that is also within the center alongside the lengthy side of the bath. Like the one ended bath it is the identical height throughout the highest of the bathtub and it sits on 4 feet of 1 style or another..
A slipper bathtub is a traditional single ended bath but with a the head finish of the bathtub higher than the foot end. The head end of the bathtub rises up, often with some model, to make the (heeled) ‘slipper’ shape after which the bathtub is named. Traditional slipper baths sit on four ft, typically with slipper baths the entrance toes and back toes are slightly totally different shapes and should not interchangeable. Brief slipper baths, 1500mm. are widespread in en-suites. Giant slipper baths are suitable for a very luxurious and indulgent setting. Slipper baths are sometimes however not always quite extensive and deep.
A bateau bath is a double ended version of the slipper tub, whereas the slipper bath goes up at just one finish the bateau is symmetrical and rises up at each ends. Like the slipper bathtub its usually on 4 feet, unlike the slipper bathtub there shouldn’t often be completely different feet required for the front and back. Bateau baths are discovered each with and without tap ledges for mounting taps.
A boat bath is a bateau bath without ft, instead it generally has a skirt that goes right down to a plinth which takes the weight of the tub (or a metal frame underneath may typically take the burden). Like bateau baths, boat baths are available with and with out faucet holes.
Keyhole Shower Baths
These keyhole shaped baths, where the spherical end of the bath was for a shower are very uncommon and there could be no non-bespoke manufacturers of them left, though up until not too long ago they might be bought as a non-bespoke product.